Plasma water table anti-corrosion fluid options
WEBSep 26, 2020 · 1 teaspoon of Physan 20 (anti fungus) 1.5 oz Blue food-grade dye (contrast additive) Mix well, treats 75 gallons of water. To make your life easy, mix well with 75 oz of water and put in a gallon jug. Then, every time you need to add ‘solution’ to your system, mix one ounce (2 TBS), with each one gallon of water.
Water table fluid - Tips and Tricks - Langmuir Systems Forum
WEBAug 7, 2018 · Definitely. Although the water table will trap a lot of the typical particulates that come from plasma cutting, it’s worth using a respirator. I use one that fits under my faceshield. It’s especially important if you do galvanized metals. I wear shaded glasses when doing quick work and the face shield & respirator when monitoring a long job.
YesWelder Cut-65DS - Plasma Cutters - Langmuir Systems Forum
WEBFeb 6, 2024 · Just because its a non-touch start does not mean its a non-high frequency plasma cutter. There are a lot of non-touch plasma cutters that are high frequency and will not work with the Langmuir table. Now if this is the non-high frequency plasma cutter with the so called ipt40 torch then most of your problem is the consumables.
Fonts specifically for plasma cutting - Langmuir Systems Forum
WEBJan 27, 2021 · Thank you. jamesdhatch January 27, 2021, 4:53pm 7. john_s: Any font can be used for plasma cutting. There are some that just won’t work well though. Papyrus comes to mind Any font with extremely fine detail flourishes or stroke portions can lose those details when the plasma’s kerf is accounted for.
Cut charts for everlast plasma - Langmuir Systems Forum
WEBSep 18, 2020 · I believe 70 psi is what that plasma wants. You have lights on the front panel that will tell you when you have the correct air pressure. mechanic416 September 19, 2020, 4:59pm 5. 1.0mm/50 amp, 1.1mm/60 amp, 1.2mm/70 amp and 1.3mm/80 amp. You could use these cut charts to help up to 60 amps! These are only starting points.
Plasma cutter not cutting all the way through at some parts
WEBJan 7, 2021 · Hey there, This has been a recent problem with my plasma cutter + CNC table combination. It was at the point that there was dross built up so much on both sides of the sheet metal, the cuts were wavy, and the nozzle was accumulating molten metal. I immediately thought it was the filter which I changed and there was actually a lot of improvement made. Still though when I cut 18G mild steel at ...
Wiring Titanium 65 - Langmuir Systems Forum
WEBMar 6, 2024 · Wiring Titanium 65. gwright88 March 6, 2024, 1:01am 1. Say what you will, but I need some serious help. This is my first plasma table (crossfire pro) I bought to use around our Hydraulic shop for personal use. Everything’s been pretty easy to assemble, but am I in no way electrician or well-versed in plasma tables.
Plasma Cut chart - Tips and Tricks - Langmuir Systems Forum
WEBThanks. mechanic416 March 5, 2022, 10:43pm 8. This is what I have found to work with most plasma cutter nozzles/tips that most people have in their shops or garages. NOTE: Orifice hole size 1mm = .03937". 20 amp tip - 0.6mm/.025" - 15 to 20 amps - 50 to 55 psi. 30 amp tip - 0.8mm/.030" - 21 to 30 amps - 55 to 60 psi.
Not piercing and/or cutting all the way (solved) Plasma cutter failed
WEBNov 21, 2022 · Air pressure to the back of the plasma cutter should be 100 to 120psi with a 3/8" hose. Air pressure set on the plasma cutter for cutting should be 70 to 75 psi. You have a S45 style torch a picture of the consumables and size your using would help.
Plasma cutter grounding - Langmuir Systems Forum
WEBSep 17, 2018 · jamesdhatch May 20, 2020, 3:39pm 3. toolboy: Clamp ground to work piece. The caveats are to make sure you are clamping to a point that won’t be freed from the rest of the material mid-cut or you may lose the arc (might not depending on the current path through the slats, but not guaranteed). The other is to try to keep it close to where you ...